Akko 5087 V5 HE TKL magnetic switch keyboard in black and white

Akko 5087 V5 HE and 5087 V5 TMR: TKL Magnetic Switch Gaming Keyboards, Dual 8K

The 5087, now with magnetic switches inside

Akko's 5087 has been a tenkeyless staple for years. The V5 keeps the shape and swaps the guts for magnetic switches, so every one of its 88 keys now reads how far it is pressed rather than whether it is pressed. That is what makes Rapid Trigger possible: a key resets the instant you start to lift, down to 0.005 mm of movement, and your actuation point can sit anywhere from 0.1 mm to full travel, set per key in 0.005 mm steps. Counter-strafes land when you decide, not when the switch gets round to it.

Both versions run at 8000 Hz on the cable and over 2.4 GHz, with Bluetooth as the third mode for a laptop, and carry a battery of around 10000 mAh so the high polling rate and the lighting do not send you back to the cable every evening. The difference is the sensor under the keys. The 5087 V5 HE uses Hall effect sensors and comes in Black or White. The 5087 V5 TMR uses tunnelling magnetoresistance sensors, accepts ordinary mechanical switches as well as magnetic ones, and comes in Carbon Fibre Black or Glassy Carbon Fibre White. The section below sets them side by side.

HE or TMR?

5087 V5 HE

Hall effect sensing, the established magnetic switch technology. Polycarbonate plate, dual-side RGB with north and south LEDs behind shine-through caps, Black or White case. Takes Akko Prism and other mainstream magnetic switches. The value pick.

5087 V5 TMR

TMR sensing, which Akko rates at 50 percent higher trigger precision, 90 percent lower power per sensor and a 47 percent wider operating temperature range than Hall effect, with a 16000 Hz scan rate. Aluminium plate, carbon-fibre-textured double-shot Cherry profile caps with south-facing RGB, Carbon Fibre Black or Glassy Carbon Fibre White. Takes magnetic switches and standard 5-pin MX mechanical switches on the same PCB.

5087 V5 HE 5087 V5 TMR
Sensor Hall effect TMR
Scan rate Not stated 16000 Hz
Switch support Magnetic switches Magnetic and mechanical (5-pin MX)
Plate Polycarbonate Aluminium
Lighting Dual-side (north and south LEDs) South-facing
Keycaps Shine-through, top and side legends Double-shot Cherry profile, carbon-fibre texture, side-printed
Colours Black, White Carbon Fibre Black, Glassy Carbon Fibre White
Shared 88-key TKL, Akko Prism linear switches, 0.005 mm Rapid Trigger, dual 8K, Bluetooth 5.0, 10000 mAh, gasket mount, ARM Cortex-M4, Akko HUB
Akko 5087 V5 HE and TMR Rapid Trigger with 0.005 mm reset sensitivity Akko 5087 V5 HE and TMR polling at 8000 Hz wired and 2.4 GHz

Akko Prism switches, or bring your own

The stock switch is Akko's Prism magnetic linear: 30 gf at the top of the stroke rising to 55 gf at the bottom, 3.5 mm of travel, rated for 100 million presses. Light enough to hover on for movement keys, firm enough at the bottom to feel where you are. The sockets are 5-pin MX hot-swap and both boards take other magnetic switches too. Akko's HUB software has a switch profile list; pick the switch you have fitted and the board calibrates to it, with the listed switches guaranteed to 0.01 mm precision. The TMR version goes a step further and reads ordinary mechanical switches on the same PCB, so you can run a magnetic WASD cluster and your favourite tactiles everywhere else.

Under the switches is an ARM Cortex-M4 processor that handles the sensing maths and recalibrates itself for temperature between -20 and 80 degrees, so the actuation point you set in winter is the same one you get in a warm room in July.

Akko 5087 V5 HE cross-compatible with mainstream magnetic switches, switch profile selection in Akko HUB
ARM Cortex-M4 processor in the Akko 5087 V5 HE and TMR Akko 5087 V5 HE and TMR 10000 mAh battery

Gasket mount, eight layers deep

Akko has built the 5087 V5 like one of its enthusiast kits: a plate sitting on silicone gaskets, Poron plate foam, an IXPE switch pad, a PET sheet, bottom foam and an EPDM layer under the PCB. The HE uses a polycarbonate plate for a softer, warmer bottom-out; the TMR uses aluminium for a firmer, crisper one. Either way the plate has somewhere to flex and every cavity that could ring has something soft in it. Two-stage flip-out feet give two typing heights on top of the flat position.

Exploded view of the Akko 5087 V5 HE: polycarbonate plate, silicone gasket, Poron, IXPE, PET, EPDM foams and 10000 mAh battery

Refreshed at 500 Hz

On the HE each key has north- and south-facing LEDs, so the top legends and the side legends both light evenly instead of one side glowing and the other fading out. The TMR runs south-facing LEDs behind its double-shot carbon-fibre-textured caps, where the side print catches the light. Both refresh at 500 Hz, which you notice most on reactive effects: ripples and waves move smoothly rather than stepping. More than fifteen presets are built in, and HUB lets you draw your own.

Akko 5087 V5 HE in white and black with 500 Hz ARGB lighting
Akko 5087 V5 HE dual-side RGB LEDs with north and south facing diodes Akko 5087 V5 HE shine-through keycaps with top and side legends Akko 5087 V5 HE flip-out foot for adjustable typing height

The gaming toolkit

Snap Key

Akko's SOCD handling. Press A while holding D and the last input wins instantly, with no dead frame between strafes.

Mod-Tap

One key, two jobs. A light tap does one thing, a deeper press another, with the depth split set at 0.5, 1.0, 2.0 or 2.5 mm.

Dynamic Keystrokes

Up to four actions on a single key, triggered at different depths on the way down and the way back up.

Toggle Key

Turn a tap into a hold, or into a rapid repeat, for keys you would otherwise have to pin down.

Three modes, two systems

A switch on the back edge moves between 2.4 GHz, Bluetooth and USB-C, and a second one flips the layout between Windows and Mac. The 8000 Hz rate applies to the cable and the 2.4 GHz receiver; Bluetooth is for the laptop and the tablet. Everything is set up in Akko HUB, either the desktop app or the web version at web.akkogear.com, with nothing to install if you take the browser route.

Akko 5087 V5 HE rear switches for Mac/Win and 2.4G/Bluetooth with USB-C port White Akko 5087 V5 HE on a desk with headset and mouse

Q&A & Specifications

Questions & Answers

HE or TMR, which should I buy?

HE if you want the magnetic switch feature set at the lower price, with the brighter dual-side lighting. TMR if you want the finer sensor, the aluminium plate and the carbon-fibre look, or if you plan to mix mechanical switches into the board.

Can I fit other switches?

Both take 5-pin magnetic switches, with the ones on Akko's HUB list calibrated to 0.01 mm and others possible but not guaranteed. Only the TMR also reads standard mechanical switches; on the HE they will not register.

Does 8K work wirelessly?

Yes, over the 2.4 GHz receiver as well as the cable. Bluetooth runs at a standard rate for everyday use.

Is it good for typing as well as games?

Yes. Set a deeper actuation point for work, and the gasket mount and foam stack give it a sound closer to a custom build.

Mac or Windows?

Both, with a hardware switch on the back to swap layouts.

Specifications

  • Models: Akko 5087 V5 HE, Akko 5087 V5 TMR
  • Layout: TKL, 88 keys, US ANSI
  • Sensor: Hall effect (HE) or TMR (TMR), 16000 Hz scan rate on TMR
  • Colours: Black, White (HE); Carbon Fibre Black, Glassy Carbon Fibre White (TMR)
  • Switches: Akko Prism magnetic linear, 30 gf initial / 55 gf end force, 3.5 ± 0.1 mm travel, 100M keystrokes
  • Sockets: 5-pin MX hot-swap; magnetic switches (HE), magnetic and mechanical switches (TMR)
  • Actuation: adjustable from 0.1 mm in 0.005 mm steps
  • Rapid Trigger: down to 0.005 mm
  • Processor: ARM Cortex-M4, auto-calibration -20 to 80 °C
  • Case: ABS
  • Mount: gasket; polycarbonate plate (HE), aluminium plate (TMR)
  • Dampening: Poron plate foam, IXPE switch pad, PET pad, bottom foam, EPDM foam
  • Keycaps: shine-through with top and side legends (HE); double-shot Cherry profile, carbon-fibre texture, side-printed (TMR)
  • Lighting: dual-side RGB with north and south LEDs (HE), south-facing RGB (TMR); 500 Hz ARGB refresh, 15+ effects
  • Connectivity: USB-C wired, 2.4 GHz, Bluetooth 5.0
  • Polling rate: 8000 Hz wired and 2.4 GHz
  • Battery: approx. 10000 mAh
  • Dimensions: approx. 362.4 x 134 x 31.2 mm
  • Typing angle: two-stage flip-out feet
  • Software: Akko HUB desktop, web and cloud driver; Snap Key (SOCD), Mod-Tap, DKS, TGL
  • Compatibility: Windows, macOS
Specifications

Akko 5087 V5, tenkeyless magnetic switch keyboard, 88 keys, US ANSI, in two versions. 5087 V5 HE: Hall effect sensors, polycarbonate plate, dual-side RGB with north and south facing LEDs behind shine-through keycaps, Black or White. 5087 V5 TMR: TMR sensors with 16000 Hz scan rate, aluminium plate, south-facing RGB behind double-shot Cherry profile carbon-fibre-textured keycaps, Carbon Fibre Black or Glassy Carbon Fibre White, accepts standard mechanical switches as well as magnetic. Both: Akko Prism magnetic linear switches, 30 gf initial to 55 gf end force, 3.5 ± 0.1 mm travel, 100 million keystrokes, 5-pin MX hot-swap. Actuation adjustable from 0.1 mm in 0.005 mm steps, Rapid Trigger down to 0.005 mm, ARM Cortex-M4 with automatic calibration from -20 to 80 °C. ABS case, gasket mount with Poron plate foam, IXPE switch pad, PET pad, bottom foam and EPDM foam. 500 Hz ARGB refresh, 15+ effects. Tri-mode: USB-C, 2.4 GHz and Bluetooth 5.0, 8000 Hz polling wired and 2.4 GHz. Battery approx. 10000 mAh. Approx. 362.4 x 134 x 31.2 mm. Two-stage flip-out feet. Akko HUB desktop, web and cloud driver with Snap Key (SOCD), Mod-Tap, Dynamic Keystrokes and Toggle Key.

Inside the box

Akko 5087 V5 HE or TMR keyboard, 2.4 GHz USB receiver, USB-C cable, keycap and switch puller, user manual.

Compatibility

Windows and macOS, with a hardware switch on the back to change layout; also works over Bluetooth with iPadOS and Android devices. 8000 Hz polling on USB-C and the 2.4 GHz receiver; Bluetooth runs at a standard rate. Both versions have 5-pin MX hot-swap sockets that accept Akko Prism and other mainstream magnetic switches with a profile in Akko HUB, calibrated to 0.01 mm for switches on Akko’s list. The TMR version additionally accepts standard 5-pin MX mechanical switches on the same PCB; the HE version does not. Takes any MX-stem keycap set in a standard TKL layout. Akko HUB is available as a Windows desktop app, a web driver at web.akkogear.com and a cloud driver.

Warranty

1 year manufacturer's warranty

Got questions? 🤔

Do you have any questions, or unsure if this product is compatible with your setup?