Consi Studio PCB-Mount Stabilisers V3

Stabilisers that do not need stabilising

On most keyboards the stabilisers are the part that eats the evening: clip, lube, band-aid, re-lube, still ticks. Consi Studio's V3 set is built to take that job off your hands. The wire does not sit loose in a housing and hope for the best; it is driven by a slider-crank, a central slider turning on a fixed pivot, so the wire is held and guided through the whole stroke instead of rattling at the ends of it. The result is a spacebar and modifiers that go down level and come back quiet, straight out of the bag.

Everything arrives tuned. The 6.25u and 7u units are fully assembled and lubed at the contact points at the factory, the 2u units the same, and Consi's position is that no further lubing or tuning is needed. For a build that is otherwise finished, that is the difference between fitting stabilisers in ten minutes and spending the night with a brush.

Slider-crank wire control

A pivoting slider carries the wire so it cannot flop, twist or tick. Less wobble on wide keys and a cleaner sound.

Clip in, then lock

The base clips into the PCB like a clip-in stab, then a screw from above expands the retention clip to lock it. No metal touches the PCB during fitting, so flex-cut and thin boards are safe.

Shims and spacers in the box

PTFE pads, 1.2 mm PCB shims, split-layout shims, stem spacers, ten screws and a screwdriver, so the set fits different PCB thicknesses and layouts without a parts order.

Set configuration

2u 4
6.25u 1, assembled and lubed
7u 1, assembled and lubed
Accessories PTFE stabiliser pads, 1.2 mm PCB shims, split-layout shims, stem spacers, 10 screws, screwdriver

Q&A & Specifications

Questions & Answers

Do I need to lube them?

No. They come lubed at the contact points and tuned. You can add more to taste, but they are made to be fitted as they are.

Will they fit my PCB?

Any PCB with standard PCB-mount (screw-in or clip-in) stabiliser cut-outs. The included shims cover 1.2 mm and thicker boards. They are not for plate-mount keyboards.

Which layouts does the set cover?

Both a standard 6.25u and a 7u spacebar, plus four 2u for Shift, Enter and Backspace. Split-layout shims are included for boards with split keys.

Can I use them on a flex-cut PCB?

Yes. The clip-and-screw mount keeps metal off the board, which is kinder to thin and flex-cut PCBs than a conventional screw-in.

Specifications

Model: Consi Studio PCB-Mount Stabilisers V3
Mount: PCB, clip-in base with screw-expansion lock
Mechanism: slider-crank wire control
Set: 4 x 2u, 1 x 6.25u, 1 x 7u
Lube: factory lubed and tuned
Included: PTFE pads, 1.2 mm PCB shims, split-layout shims, stem spacers, 10 screws, screwdriver

Inside the box

Four 2u stabilisers, one 6.25u and one 7u stabiliser (assembled and lubed), PTFE pads, 1.2 mm PCB shims, split-layout shims, stem spacers, ten screws and an installation screwdriver.

Compatibility

For PCB-mount keyboards with standard screw-in or clip-in stabiliser cut-outs, including hot-swap and flex-cut PCBs; the mount keeps metal away from the board during fitting. Shims included for 1.2 mm and thicker PCBs and for split layouts. Covers 6.25u and 7u spacebars and 2u keys for a 60% to full-size board with one spacebar. Not suitable for plate-mount keyboards.

Warranty

1 year manufacturer's warranty

Got questions? 🤔

Do you have any questions, or unsure if this product is compatible with your setup?